REL |
TITLE |
7.03 |
Layout toolbar buttons do not update during object construction |
7.03 |
Symbol is not working |
7.03 |
Incorrect Phone Number in =SCHEMAX= title box |
7.03 |
Autoexec.bat file modifies path names |
7.03 |
Choosing log scale with Autoscale checked causes errors |
7.03 |
=EMPOWER= crashed at Initialization Grid stage |
7.03 |
=MATCH= crashes when you try to view component window |
7.03 |
Space in graph measurement block causes undetectable error |
7.03 |
Tuning stops working after =EMPOWER= analysis added |
7.03 |
The Shortcut keys for Select All do not work |
7.03 |
Mirroring Microstrip/Stripline components fails |
7.03 |
Netlist in notes has old values |
7.03 |
Lossy viaholes in one-level slot-like problems |
7.03 |
Tuned variables are not replaced into netlist before closing file |
7.03 |
GPF on optimization and invalid errors when using subnetworks |
7.03 |
Can't export DXF or Gerber files without =SCHEMAX= or =LAYOUT= |
7.03 |
=EMPOWER= GPF, matrix inversion stage |
7.03 |
GPF If a new workspace with no layout is opened while layout is active |
7.03 |
=LAYOUT= always prompts for save if it is associated with a design |
7.03 |
TRF model problems |
7.03 |
=EMPOWER= is slowed by log messages on small files |
7.03 |
=EMPOWER= substrate reverts to default |
7.03 |
MIDCAP gives zero results until a parameter is tuned |
7.03 |
Dragging line in =LAYOUT= gives 0 line length error in =EMPOWER= |
7.03 |
Custom networks are reset when you try to view them |
7.03 |
Actions/Setup Variables, Yield, or optimization can cause a GPF |
7.03 |
GMAX requires DB operator when used on table |
7.03 |
Inductor disappears on 45 degree angle |
7.03 |
Correspondence of line file and input numbers in =EMPOWER= |
7.03 |
Adding 2 identical flat measurements causes freeze-up |
7.03 |
Using the MagAng operator with S11 is displayed in wrong format |
7.03 |
Will not display values for GM2 and ZM2 |
7.03 |
Empty levels in =EMPOWER= causes errors |
7.03 |
Files failed to self-register error message |
7.03 |
Thinning out does not work if the first layer in a structure is slot-like |
7.03 |
Markers Disappear when you change Properties |
7.03 |
Instability in a via through a groundplane |
7.03 |
Cancel button does not work properly in =SCHEMAX= dialogs |
7.03 |
Footprint of resistor with one port |
7.03 |
CPL Model in software still refers to LEN instead of L |
7.03 |
Log graphs can show extra lines |
7.03 |
Poured Polygon Properties change doesn't take effect until repour |
7.03 |
Graph is not Updating |
7.03 |
MCP Model fails if spacing is too small, causing optimization problems |
7.03 |
Noise parameters from passive data files aren't correct in schematics |
7.03 |
Default Simulation/Data Error |
7.03 |
EM simulation with many user-defined lumped elements crashes (GPF) |
7.03 |
No way to export S-parameters from an EM simulation when GENERALIZED is checked |
7.03 |
Footprint ports do not appear in the EM simulation |
7.03 |
Amplification in a passive circuit |
7.03 |
MATCH Components Hot Keys don't work |
7.03 |
Coplanar w/ Ground tuning |
7.03 |
Must Use Distinctive Designators when using Microstrip Elements |
7.03 |
Graph doesn't update when tuning variable in Reused Network |
7.03 |
Setting up multiple substrates in the =EMPOWER= layout table |
7.03 |
Gain in EM simulation of a lossy viahole. One-level algorithm only |
7.03 |
Losses in vias going up |
7.03 |
Equations can sometimes overwrite tuned values with original values |
7.03 |
Smith Chart Stability circles fill the wrong side of the circle |
7.02 |
Incorrect operation of cancel button |
7.02 |
Large number of simulation points creates a GPF |
7.02 |
Gerber number formatting setup is reversed |
7.02 |
Using MST,SSP, and SBN Element gives incorrect errors |
7.02 |
=EMPOWER= grid can be incorrect for series ports along Y |
7.01 |
Entering operator in place of measurement or vice-versa causes soft crash |
7.01 |
Crashing problems on NT 4 SP 5 |
7.01 |
USING statement bug |
7.01 |
Zooming on Smith charts with Stability Circles |
7.01 |
Invalid measurement on graph with log scale causes hang |
7.01 |
Missing parameters do not give an error |
7.01 |
Equation values do not update after a retranslate and revert back |
7.01 |
=SCHEMAX= not purchased message appears repeatedly. |
